Common Parts

The Standard Pier Kit uses 4 high grade galvanized J-bolts to mount the main pole to the concrete. It is usually used when moving a system and installing a new base. Rebar for the installation is not included, but you can pick it up at your local hardware store.

Fits: THOR Silver (formerly Pro Dunk Silver), THOR Gold (formerly Pro Dunk Gold) and THOR Platinum (formerly Pro Dunk Platinum), the older Pro Dunk Bronze, plus HERCULES Gold and HERCULES Platinum. It does NOT work with the THOR Diamond (formerly Pro Dunk Diamond), HERCULES Diamond or APOLLO.

This includes:

• [1] Standard Pier Kit Template Plate
• [4] J-bolt 40cm x 10cm x 16mm
• [8] 16mm hex nut
• [4] 16mm hex nut with built in lock washer
• [8] 16mm flat washer

The THOR Diamond (formerly Pro Dunk Diamond) Pier Kit works on all 12x8 THOR Diamond basketball systems. Uses high grade steel j-bolts that are galvanized and designed to be mounted in concrete. This is a 6 j-bolt pier system that is mounted into the concrete. The main pole then mounts to these bolts to hold the system to the concrete. This does not include the rebar needed for the concrete pier.

Version Notes: The THOR Diamond pier kit is designed for the current design with a 12x8 inch main pole. With this installation you will have 3 bolts on the right and 3 bolts on the left. If you have 3 bolts in front and 3 bolts in the back you can still use this pier kit. You will need to flip it around to fit your needs. The original 8x8 inch THOR Diamond used this mounting method.

This includes:

• [1] THOR Diamond Template Plate
• [6] J-bolt 50cm x 13cm x 18mm
• [18] 18mm hex nut
• [12] 18mm flat washer
• [6] 18mm lock washer

Hercules Diamond Pier Kit works on all Hercules Diamond basketball systems. Uses high grade steel j-bolts that are galvanized and designed to be mounted in concrete. This is a 6 j-bolt pier system that is mounted into the concrete. The main pole then mounts to these bolts to hold the system to the concrete. This does not include the rebar needed for the concrete pier.

This includes:

• [1] Hercules Diamond Template Plate
• [6] J-bolt 50cm x 13cm x 18mm
• [18] 18mm hex nut
• [12] 18mm flat washer
• [6] 18mm lock washer

The APOLLO Pier Kit uses 4 high grade galvanized J-bolts to mount the main pole to the concrete. It is usually used when moving a system and installing a new base. Rebar for the installation is not included, but you can pick it up at your local hardware store.

Fits: APOLLO 54 and APOLLO 60 ONLY.

This includes:

• [1] Apollo Pier Kit Template Plate
• [4] J-bolt
• [8] 16mm hex nut
• [4] 16mm hex lock nut
• [8] 16mm flat washer

This part replaces the white plastic or black cord that attaches the net to the rim. Note that this cord is NOT coupled, but it does include a metal crimp several inches from the end that functions as a stop. Watch a video on how to replace the net tie.

Version Notes: Older rims that have curly "rim horns" do not need this part. Secondly, this replacement part may not look exactly like your original.

Heavy-duty nylon white net designed for outdoor use. This does not include the net tie. If your rim uses a net tie to hold the net on we recommend checking it to make sure you do not also need a replacement net tie. Video: Watch a video on how to replace the net

This includes:

• [1] White Nylon Net

72 Inch backboard padding can be mounted on any of our 72 Inch by 42 Inch backboards. This padding is a foam coated with a latex coating to resist the elements. It covers the edge of the bottom third of the backboard.

This includes:

• [1] 72 Inch Left Side Backboard Padding
• [1] 72 Inch Right Side Backboard Padding
• [1] Stainless Steel Hardware kit package for mounting the backboard padding

60 Inch backboard padding can be mounted on any of our 60 Inch by 36 or 38 Inch backboards. This padding is a foam coated with a latex coating to resist the elements. It covers the edge of the bottom third of the backboard.

This includes:

• [1] 60 Inch Left Side Backboard Padding
• [1] 60 Inch Right Side Backboard Padding
• [1] Stainless Steel Hardware kit package for mounting the backboard padding

54 Inch backboard padding can be mounted on any of our 54 Inch by 36 Inch backboards. This padding is a foam coated with a latex coating to resist the elements. It covers the edge of the bottom third of the backboard.

This includes:

• [1] 54 Inch Left Side Backboard Padding
• [1] 54 Inch Right Side Backboard Padding
• [1] Stainless Steel Hardware kit package for mounting the backboard padding

The large Lightning Adjust actuator can be used on the THOR Platinum (formerly Pro Dunk Platinum) or THOR Diamond (formerly Pro Dunk Diamond) basketball system allowing for drill powered height adjustment and manual hand cranking. It includes the cylinder, gear box, manual crank handle and drill holster. This part will fix just about any adjustment problem you're having.

Any name brand 18 to 24 volt battery powered drill can be used with Lightning Adjust. If you don't have a drill one is available here in the parts section. If you've misplaced your manual Lightning Adjust crank handle you can find that part separately on this page as well.

Swap your standard hand crank actuator with Lightning Adjust in 10 minutes.

• Full details
• Installation video
• Installation instructions
• Replacement instructions

This includes:

• [1] Lightning Adjust [Large]
• [1] Lightning Adjust Socket
• [1] Preassembled Drill Holster
• [1] Manual Hand Crank
• DOES NOT INCLUDE DRILL

The small Lightning Adjust actuator lets you raise and lower your system with a cordless drill or by hand with the manual crank. It includes the cylinder, gear box, manual crank handle and drill holster, and it fixes just about any height adjustment problem. Swapping out a standard hand crank actuator takes about 10 minutes.

Any name brand 18 to 24 volt battery powered drill can be used with Lightning Adjust. If you don't have a drill, one is available in the parts section. If you've misplaced the manual crank handle, it is also sold separately.

Fits: THOR Gold (formerly Pro Dunk Gold), THOR Silver (formerly Pro Dunk Silver), and all BEAR models (Silver, Gold and Platinum). On the BEAR it replaces the original Bear Actuator, which we no longer carry.

BEAR owners: the manual hand crank is guaranteed to work on every BEAR model. Most drills don't have enough torque to raise a BEAR, especially the BEAR Platinum. If your drill does work, feel free to use it. Never use a corded (A/C powered) drill or an impact drill of any kind.

• Full details
• Installation video
• Installation instructions
• Replacement instructions

This includes:

• [1] Lightning Adjust [Small]
• [1] Lightning Adjust Socket
• [1] Preassembled Drill Holster
• [1] Manual Hand Crank
• DOES NOT INCLUDE DRILL

Name brand drill perfect for powering Lightning Adjust. This 18v to 24v drill includes a battery and charger.

This includes:

• [1] Name brand drill * brand may differ from photo
• [1] Battery
• [1] Battery charger

This is the crank handle only, not the complete Lightning Adjust actuator adjustment mechanism which you can find on this page and includes this part with it. If you've misplaced your handle and your Lightning Adjust mechanism is still operational this is the part you want.

This includes:

• [1] Manual Lightning Adjust Handle
• NOT THE COMPLETE LIGHTNING ADJUST MECHANISM

A replacement or spare drill bit adapter for the Lightning Adjust actuator. It connects your drill to the Lightning Adjust and is the part to order if your original adapter has been misplaced.

Fits: the Lightning Adjust Large and Lightning Adjust Small on any THOR or BEAR system. It does NOT work on standard actuators that have a permanently attached adjustment handle.

BEAR owners: your drill may not be strong enough to raise a BEAR with the drill feature, especially the BEAR Platinum. The manual hand crank will always work.

This includes:

• [1] Lightning Adjust Drill Bit Adapter

Hoops Breakaway rim features a dual spring system designed to break downwards when a player dunks on it. Video: Replace Your Net

This includes:

• [1] Hoops Breakaway Rim Plate Cover
• [2] Phillips head screws for the rim plate cover
• [1] Hoops Breakaway Rim
• [1] Net
• [4] Rim bolt with washer, lock washer, and hex nut
• Does NOT include rim spacers

Includes 4 stainless steel rim bolts, washers, and hex nuts to install the rim to the backboard. Please note, that this does not include the 4 rim spacers that go between the rim and backboard. They are sold separately.

This includes:

• [4] 7cm x 10mm hex bolt with a 17mm socket head
• [4] 10mm hex nut with 17mm socket head
• [8] 10mm flat washer
• [4] 10mm lock washer

Includes 4 rim spacers that mount the rim off the backboard so it does not touch the glass. They must be installed before the rim. Each rim spacer is a steel insert coated in soft plastic.

This includes:

• [4] Rim Spacer

Replacement Phillips head screws that attach the rim plate cover on Hoops Breakaway rims with pre-threaded holes.

Fits: Hoops Breakaway rims with pre-threaded rim plate holes. Rims made before 2015 most likely use self-tapping screws instead. We no longer carry those, but you can usually find them at a local hardware store.

This includes:

• [2] Phillips head rim plate screw

This kit includes 8 stainless steel bolts, nuts and washers used to mount the H-bracket to the aluminum frame on the backboard. 4 are used on the top and 4 are used on the bottom securing it in the center of the backboard.

Version Notes: Please measure and verify you have the same size bolts before ordering. All measurements can be found below. If you have different size bolts please submit a support request at produnk.com/support.

This includes:

• [8] 3 1/2cm x 8mm hex bolt with a 13mm socket head
• [8] 8mm small washer
• [8] 8mm large washer
• [8] 8mm lock washer
• [8] 8mm hex nut with a 13mm socket head